Changes in coke structure associated with preheating of the coal charge
Read Online

Changes in coke structure associated with preheating of the coal charge

  • 755 Want to read
  • ·
  • 88 Currently reading

Published by BCRA in Chesterfield .
Written in English

Book details:

Edition Notes

StatementBritish Carbonization Research Association.
SeriesCarbonization research report -- 87
The Physical Object
Number of Pages21
ID Numbers
Open LibraryOL14375070M

Download Changes in coke structure associated with preheating of the coal charge


  Process of carbonization of coal. The coal to coke transformation takes place as the coal is heated. When the state of fusing is reached, the layer of heated coal softens and fuses. From about deg C to deg C, the coal decomposes to form plastic layer.   The Coke and Coal Resources Committee of the Chinese Association of Coke Industry came to the conclusion that with stamped charging, consumption of coking coal and fat coal can be decreased by 14%. SO, emphasis is made on fully using the more than M . In stamp charged coke making, the stamped coal charge expands first as one body and later shrinks-the width of the final coke mass is generally more than the initial width of the coal cake. The major factors responsible for the dilation behaviour of any coal charge during carbonization are: a) rank of the coal charge; b) the bulk. Description / Shipment - Storage / Uses. Coal, a fossil fuel, is the largest source of energy for the generation of electricity worldwide, as well as one of the largest worldwide anthropogenic sources of carbon dioxide carbon dioxide emissions from coal usage are slightly more than those from petroleum and about double the amount from natural gas.

The importance of the coal blend properties as a factor in coke gasification has also been reported (Bernard et al., , ). Cokemaking conditions, i.e., BD, coking time (CT), preheating of the charge, etc., minimize some deficiencies in coal properties. The G-factor is one of the predicting tools of coke . Thus preheating of the charge was shown to result in coke with a greater number of smaller pores which are less widely spaced on average. Increasing the blend vitrinite reflectance generally reduces porosity and pore size whilst the pore-wall size shows little change although this . Institute for Chemical Processing of Coal, Zamkowa 1, Zabrze, Poland, [email protected] Abstract: The density of the coal charge plays an important role in the coke quality. The increase of the bulk density usually improves the coke strength due to increased coal particle contact and increased coke . the coal sample and then the sample is pressed for 30 seconds under a 6lk mass. The sample is rapidly coked in an electric furnace to °C in 15 minutes. The coked is weighed (M), placed in a small drum and rotated for 5 minutes at 50+/- 2 rpm. The coke residue is screened at 1mm and the weight of the +1mm coke (M1) is determined. The +1mm.

Coal, Coke and Coal Chemicals: Introduction & Historical Background Coal is a carbonaceous rock, it is not a mineral with fixed composition. Consequently, it does not have a fixed formula. It is known that coke was an article of commerce among the Chinese over years ago and in the middle ages it was used in the arts and for.   coal, coal blend, coke, coke oven, fluidity, MMR, vitrinite, wall pressure, Selection of Coal for inclusion in Coal Blend in Coke Making Blending of coals is necessary from economical point of view by reducing the percentage of high cost, prime or hard coking coals and replacing it with medium or soft coking coals. Coal Coke. Coal Coke is created by cooking Coal in a Coke though coal coke is produced slowly in the coke oven ( minutes per piece), it is a highly effective fuel as it essentially produces double the heat content of the Coal required to create has a heat content of ( in Railcraft), whereas Coal Coke has a heat content of After the coke oven is charged with coal, heat is transferred from the heated brick walls to the coal charge. In the temperature range of –°C the coal decomposes to form a plastic layer near the walls. From to °C, there is marked evolution of aromatic hydrocarbons and tar, followed by resolidification into semicoke.